Configuration VA: Customized for the V-Amp Series
This video shows you the EurekaPROM-enabled FCB1010 and the V-Amp Pro in action:
OverviewThree Modes, easily switched between using the Up/Down pedals:
- Effects Mode: Turn individual effects on/off in stompbox-like fashion, with state reflected on the pedal LED
- Presets Mode: Easily enter presets 1A-25E
- Favorite Presets Mode: Allows you to store and recall your 10 favorite presets with the push of a pedal!
Expression Pedals programmed for wah & volume. MIDI activity LED. And waterproof labels!
Modes
Switch between modes with UP/DOWN pedals.
1) EF: Effects
|
Reverb On/Off
CC22
6 |
Post-FX
CC59
7 |
Gate
CC25
8 |
Amp
CC61
9 |
Tap Tempo
CC64
10 |
|
Pre-FX On/Off
CC44
1 |
Drive On/Off
CC26
2 |
FX On/Off
CC21
3 |
Delay On/Off
CC54
4 |
Wah On/Off
CC27
5 |
Notes:
- Turn Effects on/off!
- Requires 2 MIDI cables connected (FCB MIDI out-to-V-Amp MIDI in & FCB MIDI in-to-V-Amp MIDI out).
- Effects state for pedals 1-9 is automatically updated on the pedal LEDs.
2) Pr: Presets
|
Bank Decrement
6 |
Bank Increment
7 |
8 |
9 |
Tuner On/Off
10 |
|
A
1 |
B
2 |
C
3 |
D
4 |
E
5 |
Notes:
- Enter Presets 1A-25E!
- Enter preset A-E using pedals 1-5.
- Decrement/Increment bank using pedals 6 & 7. Bank displayed in 7-segment display.
- Pedal 10 toggles the Tuner on/off.
3) FP: Favorite Presets
|
Memory Location 6
6 |
Memory Location 7
7 |
Memory Location 8
8 |
Memory Location 9
9 |
Memory Location 10
10 |
|
Memory Location 1
1 |
Memory Location 2
2 |
Memory Location 3
3 |
Memory Location 4
4 |
Memory Location 5
5 |
Notes:
- Store 10 of your favorite Presets for 1 press recall!
- To store a Preset:
- In Pr mode, select preset.
- Press UP to enter FP mode.
- Press and hold the pedal you wish to store the Preset for about five seconds. The 7-segment display will flash when stored.
- Leave FP mode.
- To recall a Preset, press and release the pedal of your choice. Note that the Program Change command is sent on the release, not the press.
|
Wah
MIDI CC1
Left |
Volume
MIDI CC7
Right |
MIDI Activity LED
- In 1-cable mode, the LED is on when MIDI is sent, off otherwise.
- In 2-cable mode, the LED is off when MIDI is sent/received, on otherwise.
VA FAQ
What do I need for this setup?
A Behringer V-Amp Series processor, a Behringer FCB1010, and one or two MIDI cables depending on your preferred mode of operation.
What do you mean "one or two MIDI cables depending on your preferred mode of operation"?
You may operate this in 1-cable mode, but EF mode is not functional. In two-cable mode EF mode is functional with effect state reflected on pedal LEDs.
Even though I have both MIDI cables connected, when I turn on my V-Amp series processor & EurekaPROM-enabled FCB1010 two-cable mode isn't detected.
The EurekaPROM-enabled FCB1010 boots faster than the V-Amp processor, so if you turn them on simultaneously the EurekaPROM won't detect the return MIDI cable. The solution is to turn on the V-Amp processor first and let it finish booting before you turn on the EurekaPROM-enabled FCB1010.
|
|
