Discontinued Product


A3
AdrenaLinn
III
VA
Behringer
V-Amps
Vb
Behringer
Bass
V-Amps
11
Avid
Eleven
Rack
G-
TC
Electronics
Po
Line6
PODs
bo
BOSS/
Roland
PP
Programmable
EurekaPROM1.1

Configuration G-: Customized for TC Electronic processors

This video shows you the EurekaPROM-enabled FCB1010 and a G-Major 2 in action:

Overview

Four Modes, easily switched between using the Up/Down pedals:
  • Effects Mode: Turn individual effects on/off in stompbox-like fashion, with state reflected on the pedal LED
  • Presets Mode: Easily enter presets 1-100, on Banks 0-9. 1000 presets!
  • Favorite Presets Mode: Allows you to store and recall your 10 favorite presets with the push of a pedal!
  • Specials Mode: Change the expression pedal definition to modify 10 effects parameters!
Expression Pedals programmed for 10 effects & volume. MIDI activity LED. And waterproof labels!

Modes

Switch between modes with UP/DOWN pedals.

1) EF: Effects

Notes:
  • Turn Effects on/off! 
  • Supports 1 MIDI cable (FCB MIDI out-to-TC Electronic processor MIDI in). 
  • LEDs do not automatically update, but they still have state, three in fact: off, on, blip (for unknown effects state). 
  • You assign the effect to the CC# in the TC Electronic processor. 

2) Pr: Presets

Notes:
  • Enter Presets 1-100, Banks 0-9. 
  • Select Banks with Pedal 1 & 6. Bank displayed in 7-segment display. 
  • Use Pedals 2-4 & 7-9 to select specific preset. Displayed in 7-segment display. 
  • Press Pedal 5 to send the MIDI Program Change command to the TC Electronic processor. 
  • With Pedal 10 on, a Program Change command is sent with each preset/bank change. With Pedal 10 off, Pedal 5 must be pressed for the Program Change command to be sent. 

3) FP: Favorite Presets

Notes:
  • Store 10 of your favorite Presets for 1 press recall! 
  • To store a Preset: 
    • In Pr mode, select preset, press Send (Pedal 5). 
    • Immediately Press UP to enter FP mode. 
    • Press and hold the pedal you wish to store the Preset for ~5 seconds. The 7-segment display will flash when stored. 
    • Leave FP mode. 
  • To recall a Preset, press and release the pedal of your choice. Note that the Program Change command is sent on the release, not the press. 

4) SP: Specials - Expression Pedal CC Assignment

Notes:
  • Change the left expression pedal CC assignment! 
  • The left pedal defaults to CC#13, but can be assigned to CC#13-22. 

MIDI Activity LED

  • The LED is on when MIDI is sent, off otherwise. 

G- FAQ 

What do I need for this setup? 
A TC Electronic G-Force, G-Major, G-Major 2, G-Sharp, and Nova, a Behringer FCB1010, and a MIDI cable.

How does this work with the G-Sharp?
Pr & FP mode work the same. (Note that the bank is ignored by the G-Sharp). EF & SP would affect these following:

SP: PreDelay
6
EF: Tap Tempo
SP: Decay
7
EF: Bypass
SP: Color
8
EF: Effects On/Off
CC82
9
EF: Reverb On/Off
CC83
10

SP: Effects Mix
1

SP: Reverb Mix
2

SP: Dig Input Level
3

SP: Timing
4

SP: Feedback
5


Have more questions? Check our Forum, or Contact us!