Configuration G-: Customized for TC Electronic processors

This video shows you the EurekaPROM-enabled FCB1010 and a G-Major 2 in action:


Five Modes, easily switched between using the Up/Down pedals:
  • Effects Mode: Turn individual effects on/off in stompbox-like fashion, with state reflected on the pedal LED
  • Presets Mode: Easily enter presets 1-100, on Banks 0-9. 1000 presets!
  •  Improved in EurekaPROM2!  Favorite Presets Mode: Allows you to store & recall your 10 favorite presets with the push of a pedal!
  • Specials Mode: Change the expression pedal definition to modify 10 effects parameters!
  •  New to EurekaPROM2!  Effects & Presets Mode: Access Effects mode pedals 1-5 & Favorite Presets pedals 6-10 in one layout
Expression Pedals programmed for 10 effects & volume. MIDI activity LED. And waterproof labels!


Switch between modes with UP/DOWN pedals.

1) EF: Effects

  • Turn Effects on/off! 
  • Supports 1 MIDI cable (FCB MIDI out-to-TC Electronic processor MIDI in). 
  • LEDs do not automatically update, but they still have state, three in fact: off, on, blip (for unknown effects state). 
  • You assign the effect to the CC# in the TC Electronic processor. 

2) Pr: Presets

  • Enter Presets 1-100, Banks 0-9. 
  • Select Banks with Pedal 1 & 6. Bank displayed in 7-segment display. 
  • Use Pedals 2-4 & 7-9 to select specific preset. Displayed in 7-segment display. 
  • Press Pedal 5 to send the MIDI Program Change command to the TC Electronic processor. 
  • With Pedal 10 on, a Program Change command is sent with each preset/bank change. With Pedal 10 off, Pedal 5 must be pressed for the Program Change command to be sent. 

3) FP: Favorite Presets

  • Store 10 of your favorite Presets for 1 press recall! 
  • To store a Preset: 
    • In Pr mode, select preset via the EurekaPROM-enabled FCB1010. 
    • Press  & Hold the UP pedal until the 7-segment display begins to flash FP. 
    • Press the pedal you wish to store the Preset. The 7-segment display will flash when stored. 
  • To recall a Preset, press and release the pedal of your choice.

4) SP: Specials - Expression Pedal CC Assignment

  • Change the left expression pedal CC assignment! 
  • The left pedal defaults to CC#13, but can be assigned to CC#13-22. 

5) EP: Effects & Presets

  • To get to EP mode:
    • Go to EF mode.
    • Press & Hold the UP pedal until both the EFfects LED & Favorite Presets LED are both lit.
  • Pedals 1-5 are from EFfects mode.
  • Pedals 6-10 are from FP mode.

MIDI Activity LED

  • The LED is on when MIDI is sent, off otherwise. 


What do I need for this setup? 
A TC Electronic G-Force, G-Major, G-Major 2, G-Sharp, and Nova, a Behringer FCB1010, and a MIDI cable.

How does this work with the G-Sharp?
Pr & FP mode work the same. (Note that the bank is ignored by the G-Sharp). EF & SP would affect these following:

SP: PreDelay
EF: Tap Tempo
SP: Decay
EF: Bypass
SP: Color
EF: Effects On/Off
EF: Reverb On/Off

SP: Effects Mix

SP: Reverb Mix

SP: Dig Input Level

SP: Timing

SP: Feedback

Have more questions? Check our Forum, or Contact us!